KOMODO ACCESSORIES (Grips, Cages, Handles...)

[rand thompson]

Ignite Digi Keystone for RED KOMODO


By Newsshooter


Article
https://www.newsshooter.com/2020/06/29/ignite-digi-keystone-for-komodo/

Ignite Digi Website
https://www.ignitedigi.com.au/products/ignite-digi-komodo-keystone?variant=32236610682946


Shape Handles website
https://www.shapewlb.com/camera-handles/


Shape Handles pictured in photos below
https://www.shapewlb.com/shape-nucleus-double-quick-trigger-grips

Also this one
https://www.shapewlb.com/double-quick-handle-arri-rosette-single-shadow

 

[Matt Beardsley]

Awesome. Looks like this Ignitedigi setup might be just the ticket to get a Komodo well balanced on Movi Pro with glass and motors. Looks like the CG with any chunky lens is going to fall forward of the lens mount (crazy)

 

[yann LHENORET]

Make some room for KOMODO LINK (Top Pins to USB-C interface):

 

[Thomas B.]

Hey guys,

I don't want to break the party, I just realized - while looking at KOMODO LINK - that it seems like you can't mount this adapter when using KipperTie's Revolva. *already imaging Revolva-users cutting off the protrusion with the 1/4"-20 threads*
Mounting a NATO rail for using a Top handle/accessories would have been possible by using longer screws, "sandwiching" or squeezing the adapter between KOMODO and the NATO rail, instead of designing a interfering protrusion.
38 or 40 pins, but using only 12 pins? I hope someone makes more use of the potential of the top interface.
I was hoping for a kinda-USBout for powering smartphone(monitor)+R/S trigger+lens control-side handle anyway, so let's wait and see what's still in development. (no complaint at all, it definitely is a nice basic adapter, it was just a thought - hope dies last)
The handle could be powered by an external source, let's say a Canon LP-E6 battery, if power consumption is a problem.

 

[Joesef o.]

I've been looking but cant seem to find out if there's any bottom riser base plates available with ingratiated 15mm rail holes that are the correct height for standardized 15mm lw mattebox to lens / rails yet?

Something similar to these https://www.bhphotovideo.com/c/prod...tangerine_b4004_0015_sony_fs5_left_field.html

https://www.bhphotovideo.com/c/product/1484508-REG/smallrig_dbm2266b_baseplate_for_bmpcc_4k.html

https://www.bhphotovideo.com/c/product/1421919-REG/smallrig_1798_tripod_mounting_kit_with.html


With a Komodo riser measured out for proper rails to lens / matte box distance... Also anyone know the riser height needed in general ?

 

[Bob Gundu]

I've been looking but cant seem to find out if there's any bottom riser base plates available with ingratiated 15mm rail holes that are the correct height for standardized 15mm lw mattebox to lens / rails yet?

Something similar to these https://www.bhphotovideo.com/c/prod...tangerine_b4004_0015_sony_fs5_left_field.html

https://www.bhphotovideo.com/c/product/1484508-REG/smallrig_dbm2266b_baseplate_for_bmpcc_4k.html

https://www.bhphotovideo.com/c/product/1421919-REG/smallrig_1798_tripod_mounting_kit_with.html


With a Komodo riser measured out for proper rails to lens / matte box distance... Also anyone know the riser height needed in general ?

Bright tangerine and wooden camera will have theirs out soon.

 

[joshua csehak]

*already imaging Revolva-users cutting off the protrusion with the 1/4"-20 threads*

The bench grinder's there for a reason! XD

 

[Doryus Sniper Jones]

Cowboy

Cowboy

A little recap of what's coming from GDU for KOMODO:

Handles seem to be attached in two different ways, the oneon the left is not exactly the same as the right one (maybe it's just me...):

Any new information or ETA the on GDU Cowboy Handles for the Komodo?

 

[Björn Benckert]

Red brought two really good things to the film community. r3d´s and nato rail. Every edge, or surface of a cage, plate or what ever I think should be nato rail shaped. I hate the bolt on things that takes tools to unmount, screws that disappear etc.

 

[joshua csehak]

Red brought two really good things to the film community. r3d´s and nato rail. Every edge, or surface of a cage, plate or what ever I think should be nato rail shaped. I hate the bolt on things that takes tools to unmount, screws that disappear etc.

+1

+11, really. This one goes to 11.

 

[Adam D. Ouellette]

Wheres the handle with the start and stop record button and the timecode box Would love to buy those right away!

 

[Mestizo Devon]

Make some room for KOMODO LINK (Top Pins to USB-C interface):

Damn, I feel like the side handle and Komodo link should have been tied together.... Maybe not enough bandwidth....

 

[Adam D. Ouellette]

I really hope that someone makes a hand grip for this at the correct distance for a single hand operator. This camera is so incredibly small it would be great for someone to make something similar to what you can get with a medium format camera, so far I'm not seeing that anywhere. Obviously this will be a specific use case that is not for everyone but I know for myself that I would use this constantly. All of the grips out there right now are designed for two handed operation. The GDU handles that have been showcased lately do not allow for this.

Here's an example.

Grips like these have been suggested to me thus far

Again the problem here is that the distance between the body of the camera and the handle is too great. When the distance between the camera body and grip is designed for two hand operation and you use it for single hand, you can't brace your wrist against the camera body itself. Immediately it becomes a lot harder to keep the camera steady and all that strain goes onto your wrist flexor. As soon as the distance between the grip and the body is eliminated the strain and control is transferred to your primary forearm muscle (brachioradialis) and it makes doing single hand operation much easier. Without this fatigue sets in very quickly because both forearm muscles are fighting to keep your arm steady.....this is not a common problem, as there have been very few cameras that have been small enough for this to work. One hand on the grip and one on the zoom, if the grip is offset properly you could operate one handed for a very, very long time. Those of you that have shot photographs on a medium format camera probably know what I am referencing. The Mamaiya 645 Tl Pro grip is exactly like this.


Currently the closest solution I have found is if smallrig does not change the design of their cage at all and the rosette remains on the right side. You then pair this with a kino grip, which is attached to this post.
It would be a real lost opportunity if nobody makes this. A grip that bolts into the right side of the camera body where the timmy ribs would go. I do really like the portkeys grip but its still too far out from the camera body.

One of the things about the komodo that really appeals to me is that I spent most of 2019 working in remote locations, sometimes extremely remote locations, having to hike all the gear in. Basically every pound counts and lugging a Hydrogen body, a set of ronford legs and lenses in a backpack with camping gear always sucks when you've got miles to hike before you shoot. This camera is a massive relief for that and still fitting into a redraw post pipeline. This is obviously very different from those of you using this camera in a studio or commercial shoots, but if nobody produces this I may have to make it myself. For all I know someone may already be making it.

 

[Chuks Ude]

Looks like Tilta will have a KOMODO rig coming soon:

https://www.youtube.com/watch?v=foKy1N-mCz4

 

[yann LHENORET]

Very nice plate. Is it me or the rosettes are oddly positioned? Or maybe they can be placed elsewhere?

 

[George Nathanson]

Looks like Tilta will have a KOMODO rig coming soon:

https://www.youtube.com/watch?v=foKy1N-mCz4

Hmm.... Vlock plate...Wonder if it's got internal power for hot-swap looks pretty bulky to just be adapter :001_huh:

 

[rand thompson]

Wooden Camera RED approved Komodo Accessories


By Newsshooter


Article
https://www.newsshooter.com/2020/07/15/wooden-camera-red-approved-komodo-accessories/

Wooden Camera Website
https://woodencamera.com/pages/red-komodo-accessory-kits

 

[Matt Beardsley]

ooh, I like the look of Wooden Camera's "B Box" breakout for gimbal/drone work assuming the CTRL port speaks Movi Pro like DSMC2 cameras. 5-pin timecode, interesting; don't need Genlock, but still. Exciting times

 

[J. Orlandi]

It doesn't look like that timecode box allows enough space to have a battery in the first slot... They might wanna rework that cable length. And I personally hate the design, structure, price, and ergonomics of the 15mm base plate... I'll look elsewhere for now I guess.

 

[Phil Holland]

It doesn't look like that timecode box allows enough space to have a battery in the first slot... They might wanna rework that cable length. And I personally hate the design, structure, price, and ergonomics of the 15mm base plate... I'll look elsewhere for now I guess.

I can 100% confirm that you can use a BP-955 in camera-rear-left slot with the B-Box and their V-Mount adapter, which also allows for hot swap to a V-Mount or G-Mount. Also their battery plate allows for DC-IN to also be pulled and switch to V-mount or BP-Mount as well. You can use the 975 too, but it's less flexible and weird. Without a BP you can rig flush to the body.

Perhaps a hot take, maybe too much of one. I don't want to get too preachy because I feel fortunate to have tested the bulk of what's coming and stuff that hasn't been announced, don't necessarily want to give anybody free marketing really either for that matter, but if you want an opinion...... This WC gear and something else coming are the most well thought out and flexible for production use IMO. I will say Tilta's battery plate in particular is very interesting and a unique take on things while keeping V-Mount tidy and cable-free. Their stuff will give you your value option for sure. There's a top plate coming that's pretty badass too from another entity, but it's on the pricier side.

There's other stuff coming in this price range from other manufacturers, a bit higher even, and a bit lower as well as notably lower.

I'm curious about other's thoughts on price, because frankly with a battery plate, all the QR plate stuff, top handle, monitor mounts, and rod support I thought this was a pretty affordable option.

The hard one coming from a DSMC2 primary shooter in relationship to all of this is I really did the whole cable-less thing to the extreme. Komodo will inspire the use of D-Tap for accessories for sure mainly because of how small the camera is as well as it being a pretty low power ecosystem. An interesting balance between being able to run a camera I guess for 6 hours off a brick versus 2 hours really.