FS: AUTODESK FLAME 2011

[Björn Benckert]

We are selling this setup with included delivery and on site installation. Everything needed to get going down to the vacom pen.
This system is taken of suport but could go under the owner transfer system and later be updated. But frankly it's a great working pice of machinery as it is and If it was my choice I would buy it and use it as is.

Here is a link to full inventory and price: http://wordpress.syndicate.se/autodesk-2011-flame-for-sale/

If wanted we also have a separate flame 2009 license that we do want to sell as well. Now for a lowered price of 8k USD. This licence is great if you want to go for a new Flame 2013 as you can use it as an upgrade step and save huge on doing so. for more info see separate thread. http://www.reduser.net/forum/showthread.php?70711-WTS-Auto-desk-FlAME-2009-license&highlight=

 

[Frank Cueto]

Why The sale?

 

[Björn Benckert]

We have to many. I got 3 setups and I use one... I love flame. Especially flame 2012, do not like what happen to flame 2013, maybe I get it in the end but as of now I think they messed things up. And believe it or not our office only have a small little machineroom, we built it that way on purpose just so we would be forced to run a tight ship without gathering up on to much gear and I can simply not run all 3 in there without overheating. So 2 has to go.

And I can only say the way flame 2011 and forward works with r3d's for compositing grading and finishing is unmatched by all other systems I tried and I tested more than most, and the price that we sell this unit for is ridiculously low. Remember that this was sold new 2011 by Autodesk for 2,5 million swedish wich is about 380k USD... So now a few years later you get over 300k USD discount and free instalation. I think Autodesk charge more to set up a system than we charge for the whole setup

 

[Björn Benckert]

Bump.


I thought people would jump on this... Do not be shy toss us your best offer, you might be lucky. And if you arrange your own shipping / pickup and installation, wich should not be too hard we might consider slicing the price quite a bit.

 

[Björn Benckert]

Only 2009 license for sale now... decided to clean out some space in the machineroom and install the 2011 right next to my 2012...

Having 2 of these beasts right next to each other is quite nice, a bit like having two ferraris stacked ontop of each other... lol.

https://www.facebook.com/photo.php?...43523042&type=1&theater&notif_t=photo_comment

 

[Vithya Sharma]

Facebook link notwork..

this message display

This content is currently unavailable The page you requested cannot be displayed at the moment. It may be temporarily unavailable, the link you clicked on may have expired, or you may not have permission to view this page.


and unsupporter mean?

Included are:

• 1 Autodesk Flame 2011 (unsupported)
• 1 HP 8600 Workstation
• 1 Eizo CE240W Coloredge Monitor
• 1 Wacom Intuos3 PTZ-631W Tablet
• 1 Keyboard
• 2TB Stone Disk Array
• 1 AJA box
• 1 Blackmagic miniconverter SDI Analog
• 1 Lucid 88192 AD/DA converter
• 1 Samson C-control
  
  Thank you

 

[Björn Benckert]

I means we do not have a support subscription from autodesk for this setup. They have a suport system that lets you get all updates and full internet support. But as we been on flame for 16 years now we figured that we do not need support and we make a deal with the sales people when we feel we want an upgrade.
So if you want support for it. O if you want to upgrade this system in the future then you would need to pay an owner transfer fee to autodesk first. Kind of same deal as with red cameras.

But again it's not for sale any longer, at least not for the price listed as I reconsidered and now have installed next to my Fame 2012. as the facebook picture showed...