DSMC EPIC / SCARLET Release build 5.1.51 and Beta 5.2.16

[Jarred Land]

enjoy:


https://www.red.com/downloads/

Release 5.1.51 SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v5.1.50


* Added Iris Only support for Nikon AF Nikkor 16mm f/2/8D Fisheye
* Fix camera freeze after issuing key actions with REDLINK Command Protocol
* Fix image and frame guide offset between preview and playback
* Fix missing lines from SDI output during playback
* Black Shade optimization for Dragon

https://www.red.com/downloads?release=beta


Beta 5.2.16 SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v5.2.15

* Added support for Nikon AF Nikkor 16mm f/2/8D Fisheye (Iris Only)
* Added support for Fujinon Cabrio lens
* Fix 'Error loading clip' notification when loading multiple files in playback mode
* Fix camera freeze after issuing key actions with REDLINK Command Protocol enabled
* Fix image and frame guide offset switching between preview and playback
* Fix missing lines from SDI output during playback
* Fix notification when media is full
* Black Shade optimization for Dragon
* The horizon level feature requires Gyro calibration be completed prior to use.

 

[Taylor Morrison]

will do!

 

[Ketch Rossi]

Thanks...

 

[Rick Augustus]

Thanks...

 

[Michael Kromschroeder]

Thanks Jarred

 

[Michael Tiemann]

Beta 5.2.16 SIGNIFICANT CHANGES SINCE PREVIOUS BUILD v5.2.15

* Added support for Fujinon Cabrio lens

What does this mean? Does it mean that the 19-90 now communicates FIZ metadata via the PL mount? Does it mean that Cabrio 14-28 communicates FIZ data? Does it mean that the Cabrio 25-300 communicates FIZ metadata?

Thanks!

 

[Antonio Forjaz]

up dated, thanks

 

[nick allsop]

Is there an ETA for when 5.2 is coming out of Beta?

 

[Jason Diamond]

Thanks! Been running 5.2.15 with no hiccups...

 

[jacob.schwarz]

Ran test all night on these latest build and discovered some issues with the BETA build in terms of high shutter and frame rates. If anyone is interested they can find it here.
http://www.reduser.net/forum/showth...orange-Noise-Levels-Without-Black-Shade/page4

 

[Dave Winder]

What does this mean? Does it mean that the 19-90 now communicates FIZ metadata via the PL mount? Does it mean that Cabrio 14-28 communicates FIZ data? Does it mean that the Cabrio 25-300 communicates FIZ metadata?

Thanks!

Yes, this means we can now capture the FIZ metadata via the PL mount or the PL Motion Mount. The lens still does require external power however. Communication will be established regardless of power up sequence between the lens and camera. We do plan to verify other Fuji lenses, but so far only the 19-90 is confirmed. There is a new setup step required in the Settings>Setup>Lens menu to disable power to the lens when using the Cabrio.

 

[Mike Halper]

Using v5 firmware for the first time. The audio settings are very confusing compared to before. What is rear mix? Monitor mix? Cam mix? I'm also noticing I can no longer adjust the pre-amp and levels on the front brain inputs low enough so now everything sounds terrible. Is anyone else having this issue?

 

[Eric Emerick]

Beta Scarlet M-X upgrade can’t see what mount is on the camera. I have motion mount. FYI.

 

[Stacey Spears]

Eric, try using the rediscover HW function and see if that helps. Its under setup -> maintenance.

 

[Max M.]

I can't get any timecode input on Epic Dragon on this firmware build. I tried several tc sources, lockit, f5 and c300 set to external tc, they all sync up with each other, but none works on the Dragon. TC setting in the menu are good, no idea what to do about it, any suggestions?

 

[Eric Emerick]

Eric, try using the rediscover HW function and see if that helps. Its under setup -> maintenance.

Next time. I just loaded the new non beta version and all is good.

 

[Matthew J]

I can't get any timecode input on Epic Dragon on this firmware build. I tried several tc sources, lockit, f5 and c300 set to external tc, they all sync up with each other, but none works on the Dragon. TC setting in the menu are good, no idea what to do about it, any suggestions?

I had this happen the other day on the last beta and was thinking that it was my cable or port (since the 744t would jam the F3 we had), but hopefully it's just the build itself and not the hardware.

 

[Stacey Spears]

I can't get any timecode input on Epic Dragon on this firmware build. I tried several tc sources, lockit, f5 and c300 set to external tc, they all sync up with each other, but none works on the Dragon.

5.1.n or 5.2.n? Did it work for you on the previous firmware vesrion? Nick and Doug are having timecode issues with Dragon. I just tried 5.2.16 with my SB-T and TC, Gen, and Sync all light up green.

Next time. I just loaded the new non beta version and all is good.

Did you send a log to Red to debug? You should still be able to do it even though you reverted back to older FW.

 

[Eric Haase]

enjoy:


* Black Shade optimization for Dragon

Could someone please expound on this?

 

[jacob.schwarz]

Could someone please expound on this?

Yeah, we are seeing a ton a noise in the image.