Release Camera Build 3.2.16

[Jarred Land]

RELEASE VERSIONS

SIGNIFICANT CHANGES SINCE PREVIOUS BUILD V3.0.7:

• Added 5K HD, 3K HD, 2K HD, 1K HD formats
• Added 1K WS format (Epic 400fps, Scarlet 120fps)
• Added Target REDCode feature
• Added Post Record Fan Delay (max 1 minute)
• Added 1-camera to multiple REDMote support
• Added Slate Information Dialog
• Added User RGB curves capability
• Added RMD file import/save/apply
• Added Gyro support
• Added Side Handle Key Lock Feature
• Added Audio Gain/Limiter Controls
• Added Phantom Power Support(Hardware Rev Dependent)
• Added External record mode
• Added Force Restore Feature using Power Button
• Added HD-SDI Format controls
• Added 9" LCD Touchscreen support
• Added Dual Battery Module support
• Added Rear SSD Module support
• Added OLED EVF Brightness support
• Added Playback Frame, Title and Action Guide status
• Added PL Lens short circuit detection
• Added HDMI 1080p/720p refresh rates of 24,25,30,50,60
• Enhanced Keys assignment dialog
• Enhanced Preset dialog
• Enhanced Playback load notifications and error handling
• Enhanced UI usability
• Enhanced AF capability
• Camera Name defaults to camera type (i.e., SCARLET/EPIC)
• Fix for Playback using EVF
• Fix for Playback support of 5K and 5K ANA
• Fix for Zoom Rocker +/- Mapping
• Fix for HD-SDI output scaling
• Fix for LCD image ‘stutter’ when panning
• Fix for camera freeze when changing AF/MF with Focus dialog open
• Fix for Zebras disappearing after disconnect/reconnect of RED monitor
• Fix for scaling of 5K clips during Playback
• Fix for HD-SDI test pattern output levels
• Fix for record error 0×00001E seen on some cameras
• Fix for multi-clip load issue in Playback
• Fix for audio in HDRx mode
• Fix for frame drift with Sensor Sync = Genlock on some cameras
• Fix for camera not completing clip recording to end of media
• Fix for camera hang mapping actions to rocker switch
• Fix for LCD w/half white screen on start-up
• Fix for RED EVF connection problems

OPERATIONAL NOTES SPECIFIC TO BUILD V3.2.16:

• Sensor Flip disabled
• Detaching monitor during playback will require reboot on monitor re-attach
• Camera powered by RED BRICK may display voltage instead of battery capacity on some cameras.
• EVF black level raised in some cases
• ISO setting limited to min of 250
• Image Magnify is available during preview, but not during recording.
• HD-SDI is True Progressive and does not support 1080i or 1080 PsF signal formats.

Epic Build : http://s3.amazonaws.com/red_3/downloads/firmware/epic/Epic_build_3_v3.2.16.zip

Scarlet Build : http://s3.amazonaws.com/red_3/downloads/firmware/scarlet/Scarlet_build_3_v3.2.16.zip

Will be on RED.COM in the morning..

 

[Matt Mascheri]

Impressive. Most impressive.

Matt

 

[Bob Gundu]

nice

How's the power management and LCD flip going? hee hee.

 

[Michael Mayda]

Thank you for another batch of goodness.

 

[Jarred Land]

Power management is coming along.. high priority. You will see little small steps instead of one big step as builds go along.

 

[Mark Toia]

WOW !!!

This is a great Update Jarred... Very significant updates in there.

Thanks again. (as usual)

 

[Bob Gundu]

Awesome... thanks! Already excited the OLED takes 70% less power.

Power management is coming along.. high priority. You will see little small steps instead of one big step as builds go along.

 

[zak forrest]

dude =] perfect timing for me, thanks!!!

 

[Jim Hoffman]

Great. And the official release build too. Thanks.

 

[Trevor Meeks]

Wow... awesome. Thanks Jarred and everyone on the RED Firmware team!

 

[Les C.]

I'd been running 3.2.13 on a Scarlet without problems (no white screen, or 1/2 white screen issues), except for the 1080p24 not working.

This is a major step backwards for me.

I got the 1/2 white screen (on the RED touch LCD) right off the bat, was able to shut down by tapping in the power display area.

Then I got the full white screen. Had to hold the power button down to shut down.

Then, I got it to come up ok, set the hdmi to 1080p24 - and had the same issue I reported here for 3.2.13. The Samsung monitor that works at 1080p60 reports 'unsupported format' when Scarlet's set to 1080p24. I also was unable to get the Black Magic Intensity card to see anything at 1080p24 with 3.2.13, a resolution it fully supports.

http://www.reduser.net/forum/showth...Build-3-2-13&p=1021054&viewfull=1#post1021054

Tried rebooting. Now I've got the full white screen again.

Going to try to go back to 3.2.13.

Great feature list though, my Scarlet keeps getting better and better - just a few bugs to work out!!!

 

[Matthew Richard Harris]

Fantastic, thanks for another great update.

 

[Damien Molineaux]

Was waiting for this one!!!
For phantom, does that mean some cameras need a hardware revision, how do we know which ones, by serial number, or by testing?
I will test in any case.
Cheers,
Damien

 

[Dominik Muench]

very sexy ^^ thanks Red people.

 

[Mike Seymour]

Thanks Red - we almost get used to these free updates - but of course we never want to take them for granted.
We have come a long way and it is so great to see continual improvement.

I don't think I say it enough: really happy - really thankful


mike

 

[Jason Diamond]

Nice one!!!!!
dropping this in tmw. Keep the hits coming its been a great soundtrack so far

 

[Ketch Rossi]

Nice adds and fixes, and the Rear SSD Module is a beauty...

 

[Michael Ou]

Very excited! Excellent improvements and Thank you so much!

 

[Steve Johnson]

Thanks Jarred and RED - these updates just rock!

)

 

[PatrickW]

Awesome update.

I find the build version number system to be slightly confusing. 3.2.8 precedes 3.2.16. It is more clear that 3.2.08 is followed by 3.2.16.