Welcome to our community

Be a part of something great, join today!

Log in
  • Hey all, just changed over the backend after 15 years I figured time to give it a bit of an update, its probably gonna be a bit weird for most of you and i am sure there is a few bugs to work out but it should kinda work the same as before... hopefully :)

bug in a MC 6.0 ama 1.6

M

Maicol_Borghetti

Well-known member
Joined
Jan 17, 2008
Messages
106
Reaction score
0
Points
0
Website
www.maicolborghetti.com
MC 6.0, ama plugin 1.6.
try do this on a red file imported by ama:
right click > Source settings > move exposure, brightness, contrast all the controls are moving just jumping by step of 1.00
so 1.00 or 1.99 not make any difference. just big jump from 1.00 2.00 step.
what can I do'? where I'm wrong?
 
Try entering a value via the keypad to see if you can get to the interim values. Perhaps the left/right arrow keys allow for smaller increments. I need to get in front of a system to see for sure.

Michael
 
nothing to do also writing the value... also nothing to do if you create the setting in redcine x and try to load into source settings...
I thinks this one is a BIG bug if confirmed from other user I also was not able to export my mixed media (5d and red one) project. taking error 2034
I came back to 5.5.2 to finish my work than try again. anyway the 6.0 64bit version is super faster compared to 5.5.2 32bit.
Maic
 
Are you saying that creating a interim value in REDCINE X and saving the RMD doesn't appear in source settings when using the RMD?

Michael
 
MichaelP said:
Are you saying that creating a interim value in REDCINE X and saving the RMD doesn't appear in source settings when using the RMD?

Michael
Click to expand...

YES, the value remain the default one. I repeat MC 6.0 ama plug 1.6 redcine X build 506.
Actually I have unistalled MC 6.0 and back to 5.5.2 to finishing a work.
 
in MC v6 on Windows 7, i can change values in source settings by .01 increments; 1.10, 1.11, 1.12, etc. Either by sliding the GUI or using the left and right arrows keys after selecting the slider.
If you updated from v5.x.x, the you will want to start with fresh settings as recommended by the RED ME notes.
Michael
 
Ok I can change the value number too but this does not affect the video look. the istogram too remain blocked and just jump only when I have a valute of 1 in difference 1 2 3..
can you try again and confirm to me? I will try to reinstall all the sw..
 
Ah - you are saying that you see no difference in the image or the histogram unless it is in 1.0 increments. I'll check.

Michael
 
The histograms change with every +/- .01 increment even though the changes are very subtle. As far as picture, it does change as well, but the changes are as subtle if not more than the histogram but it will change. What is broken is the "apply" which was designed to allow changes to propagate through to the source clip loaded in the source monitor and thus be available as a signal over attached hardware to a calibrated monitor or scope.

Michael
 
must be somethings so stupid on my pc for this bug....
I just reistall all and this does not work.. such if the sistem value does not see the dot... all is scaled 100x, contrast for example 3 big jump> - 1 / -0.99 to +099 / +1 crazy! any ideas???
 
Graphics card perhaps?
 
Did you download the latest REV AMA Plug-in from Avid.com? If you upgraded from v5.x.x then you will need the new one. They are not automatically installed for the released version which can lead to these types of issues. I am not near my system, but I would download and install/re-install anyway to be sure.

Michael
 
Now wasn't that easy? ;)

Good to hear.

Michael
 
You must log in or register to reply here.
Back
Top