camera to camera sync?

[Eli Jarra]

Got an answer from John Restivo at RED that what Deanan posted does not apply to the EPIC. We will will need timecode and gunlock generators... no way around it.

interesting... if it doesn't apply to Epic, what DOES it apply to. Can't do it with Red One that's for sure... Doesn't make sense to have it on Sc. and not Epic. Confused about that one.
I spoke to support as well, he said that cable pertains to features that haven't been activated yet. Cable would be pointless to have until that happens. He said the GigE and cam-control cable are the ones to have.
So, no way to shutter sync yet BUT... I'd bet that feature is coming one day...

[Andrae Palmer]

interesting... if it doesn't apply to Epic, what DOES it apply to. Can't do it with Red One that's for sure... Doesn't make sense to have it on Sc. and not Epic. Confused about that one.
I spoke to support as well, he said that cable pertains to features that haven't been activated yet. Cable would be pointless to have until that happens. He said the GigE and cam-control cable are the ones to have.
So, no way to shutter sync yet BUT... I'd bet that feature is coming one day...

Shutter syncing does not work on a Scarlet either. Looks like Les was talking about timecode syncing and not shutter syncing.

[Nicos Ambatzis]

Hi,

Is it possible to sync a Red-MX with an Epic-X and HOW??????

[Ken Corben]

I was referring to shutter syncing instead of timecode syncing. But... do have the gig-e cable... how do you configure it for timecode syncing?

1) Purchase a $100 3BNC-T0-00 for each camera to be synched:
http://www.red.com/store/cables/prod...emo-sync-cable

2) External Tri-Level Synch Box required - this example uses the AJA GEN 10 available online for <$350. Make certain to purchase the AJA GEN 10 power supply chord that fits an independent power source. DO NOT use a D-tap to power the GEN 10 from the same battery that is powering the camera. Low voltage results in failure.

(Note: the Deneke SB-T at $1,000 provides timecode and tri-level synch in one GEN 10 size box.)

3) Set the GEN 10 dip switches - slick that they print the switch functions right on the case in a readable print.

(Suggestion - select ON for VIDEO outputs 4 & 5 on the dip switch menu. Provides cleaner cable out wrangling for 2 cameras.)

4) Power the AJA from an independent power source.

5) Connect the GREEN BNC end of the 3BNC-TO-OO cable onto the GEN 10 VIDEO OUT 1-5 as selected in set up.

( 3BNC-TO-OO cable: GREEN BNC is synch, YELLOW BNC is for timecode and WHITE BNC is Not Applicable to this set up).

6) Carefully align and connect the LEMO 00 end of the 3BNC-TO-00 cable into the LEMO synch input of the EPIC.

7) Select EXT GENLOCK and EXT JAM SYNCH in your camera settings. May require rebooting the cameras when more than 3 camera are on the same GEN 10. No further steps required in camera.

8) Provide Jam synch to all cameras with the YELLOW BNC end of the 3BNC-TO-00 cable.

(Recently tested Sound Devices 4400T from Coffey Sound and used it as the time code master clock for jam synching EPICs. Worked well. Requires BNC barrel connector and BNC to LEMO from Coffey).

The Master/Slave GIG-E cable from RED is used to slave camera controls.
http://www.red.com/store/cables/prod...raight-cable-4
For example, when the cable is connected and Master/Slave mode is properly set, one REDMOTE will activate RECORD for both cameras. Now that is my definition of slick...

[Andrae Palmer]

Ken, Thank you for the detail instructions of setting up the camera with the AJA Gen 10.

With just the gen-e cable and the camera... is it possible to share timecode from one EPIC-X to another?

[Nicos Ambatzis]

Hi Andrae and Ken,

It seem to me that both of you are, I would say, experts in this subject. I would very much appreciate it if you share with me your knowledge in the communication subject between RED-MX and EPIC-X. Thanking you both in anticipation.

[Andrae Palmer]

The RED One would need a compatible timecode cable to sync timecode. You can find it here: http://www.red.com/store/cables/prod...ecode-cable-12


So basically you need a timecode cable for the RED One and another timecode cable for the EPIC. The timecode cable for the EPIC can be found here: http://www.red.com/store/cables/prod...emo-sync-cable

There is no way to do a "camera to camera" timecode sync between the RED One and the EPIC-X.

[Nicos Ambatzis]

Thank you very much for your replay, but can you go a little further.... (where you connect the cables - any settings ????) The final aim is to shoot with both cameras the same time having the same time code for editing synchronization. Thanks again.

[Andrae Palmer]

Nicos,

Detail instructions are in the RED EPIC & RED One operation guide on how to timecode sync each camera... it wouldn't make sense for me to rewrite all of those instructions on here and even more it would take a whole lot of my time. These instructions for the EPIC start on Page 161. Page 130 & 141 on the RED One manual. "Jam Sync" is a good search term to use in both manuals for diagrams on how to verify a successful sync. The manual has a diagram of where to connect the cables. Just a reminder that each camera uses two different timecode cables and of course you will need a device that can generate timecode.

https://www.red.com/support/all/downloads

[Nicos Ambatzis]

Andrae,

Thank you very much for your help. I will read all relevant instructions within the manuals. Sorry but I didn't know. Thanks again.